Free in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Sliding glass doors
Impact garage doorsPGTCGI
Before
After
Before
After
Before
AfterCGI Windows & Doors in Sea Ranch Lakes, FL | TruePane Windows & Doors
We’re an independent CGI service provider working throughout Sea Ranch Lakes, and the one thing that separates our CGI work here from anywhere else in Broward is simple: we plan every job around the village’s own permit process and the two-sided salt air that eats aluminum faster than most contractors expect. If you need Sea Ranch Lakes Window Installation or a door repaired, replaced, or brought up to current HVHZ code, call (754) 238-2201 and we’ll walk you through exactly what your house needs. Free estimates, done on paper, side by side.
Why Sea Ranch Lakes Residents Choose Us for CGI Service
Dale Kessler started TruePane in 2008 after watching too many impact windows get set out of true and too many warranties get voided on a technicality. He grew up in Kendall, spent summers watching his father re-glaze storefronts along the Tamiami Trail, and trained at Miami Dade College’s vocational program learning to read a rough opening the way a doctor reads an X-ray. That’s the standard we bring to every CGI job in Sea Ranch Lakes.
We’ve been replacing and rebuilding CGI windows and doors in this village for over a decade now. Our techs know the Estate Series casement that pits at the sill within a few years of salt exposure. They know the Sentry Storm door hinge that seizes up in marine air. And they know the village building department’s review workflow well enough to pull permits without getting blindsided. We’re not a manufacturer affiliate. We don’t answer to CGI’s warranty department. We answer to you and to the work itself.
Every Sea Ranch Lakes job gets OEM parts where they matter, marine-grade aftermarket components where they outperform, and both warranty layers registered in writing before our truck leaves your driveway. That’s The Keystone Standard, and we’ve stood behind it for years.
Common CGI Windows & Doors Problems We Solve in Sea Ranch Lakes
- Aluminum frame pitting on CGI Estate Series casements. The salt-laden air off Lake Santa Barbara and the Atlantic, less than half a mile east, etches the sill and weakens the frame faster than almost any inland Broward address. This is Sea Ranch Lakes’ most common CGI failure, and it shows up within three to five years on original-install units.
- Seized rolled pins and hinges on CGI Sentry Storm doors. Marine air corrodes the hardware on these doors quicker than almost anywhere else in the county. A door that won’t throw or lock cleanly isn’t just an annoyance, it’s a wind-mitigation failure waiting to happen during a summer storm.
- Leaking CGI Classic Series sliders at the head. Many Sea Ranch Lakes homes date from the 1960s through early 1980s, and the original rough openings are often too shallow for the impact frame’s header. Wind-driven rain during southerly squalls finds its way in when the flashing wasn’t detailed properly.
- Salt-clogged weep holes on CGI Tribute Series fixed windows. Properties near the dune zone get sand and salt crust building up in the frame channels, trapping water inside instead of draining it. That leads to interior leaks and eventually to frame rot in the surrounding wood.
- Worn-out rollers on CGI sliding doors. We replace more rollers in Sea Ranch Lakes than in Fort Lauderdale, Hollywood, or Pompano combined. The salt air from two directions chews through factory rollers in half the time, and once they go, the door binds and the panel weight starts working against the frame.
CGI Service in Sea Ranch Lakes: What Local Conditions Mean for Your Equipment
Sea Ranch Lakes runs its own village building department, and that’s not a detail you want to discover mid-project. Every CGI window or door permit here is pulled through the village’s separate review workflow rather than Broward County’s e-permit portal. A contractor who shows up expecting a standard county submission often gets blindsided by the village’s own plan check and inspection scheduling, which adds a local bureaucratic step that isn’t present just across the city line. For a homeowner, this means an extra few days of lead time and a permit process that rewards a company that has done it before. For your CGI equipment, it means every replacement has to carry a Miami-Dade Notice of Acceptance or Florida Product Approval for impact resistance, even though the village issues its own permits. The village doesn’t waive the HVHZ requirement, it adds a layer on top of it. We pull the village permit the same day we measure, because we’ve seen what happens when that step gets skipped or delayed: the job stalls, the inspector won’t schedule, and the homeowner is left with a torn-out opening and no path to close it.
CGI Models & Products We Service in Sea Ranch Lakes
We service the full CGI residential line: the Estate Series, Classic Series, Tribute Series, and Sentry Storm. For the first five years after an install, we use OEM parts whenever they’re available, because the tolerances on impact-rated frames are exact and aftermarket components that “almost fit” don’t cut it. After that five-year mark, marine-grade aftermarket rollers, hinge pins, and weatherstripping often outlast the original pieces in Sea Ranch Lakes’ corrosion zone. We stock common CGI hardware locally so we’re not waiting on a distributor truck when your door won’t close. And we’re cautious about patching single-glazed units in pitted frames. If the aluminum shows more than shallow salt oxidation, a full frame replacement is usually more honest than a repair that will fail again in eighteen months.
We also provide CGI sales & service support for homeowners who need honest guidance on whether to repair or replace, and we quote manufacturer lines side by side on paper so you can see exactly what you’re paying for.
CGI Service Pricing in Sea Ranch Lakes
CGI service pricing in Sea Ranch Lakes depends on what failed and how far the salt has gotten into the frame. A roller replacement on a Tribute Series slider runs toward the lower end of the scale. A full frame replacement on an Estate Series casement with deep sill pitting runs higher, because we’re reframing the opening with a marine-grade stainless sub-sill and installing new PVD-coated hardware, not just swapping glass. A typical CGI slider roller replacement in Sea Ranch Lakes falls in the $180 to $340 range. Full frame replacements for pitted CGI Estate casements typically run $900 to $1,800 per opening, depending on size and how much of the surrounding rough opening needs rebuilding. Every estimate is free and written line by line, with both warranty layers registered in writing before the truck leaves. Call (754) 238-2201 for an exact quote, and we’ll measure it right the first time, or plan on coming back.
Serving Sea Ranch Lakes, FL - Our Local Coverage Area
We’re based in the Sea Ranch Lakes area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - CGI Windows & Doors in Sea Ranch Lakes
Sea Ranch Lakes requires its own village permit, pulled through the village’s separate review workflow, not Broward County’s e-permit portal. A county-only submission will not satisfy the village’s building department. We pull the village permit the same day we measure, so the job doesn’t stall waiting on paperwork. Call (754) 238-2201 and we’ll explain the exact permit path for your street.
The CGI Estate Series and Sentry Storm lines hold up best in Sea Ranch Lakes’ two-sided salt-air environment, provided the hardware is PVD-coated or marine-grade stainless from day one. The Classic and Tribute series will survive here, but their factory hardware typically needs replacement sooner. We quote hardware upgrades side by side so you can see the difference in writing.
Shallow surface oxidation can sometimes be cleaned and sealed, but deep salt pitting at the sill or on the frame face usually means a full frame replacement, because the structural integrity is already compromised and patching it will fail again. If the aluminum shows more than cosmetic pitting, we’ll tell you honestly and show you the pitting on site. That’s the square deal.
Yes. Every impact-rated window or door replacement in Sea Ranch Lakes must carry a Miami-Dade Notice of Acceptance or Florida Product Approval, regardless of who issues the permit. The village’s permit process doesn’t waive the HVHZ requirement. We register both warranty layers in writing and verify the NOA before we order anything.
Sea Ranch Lakes sits between a freshwater lake and the Atlantic, so salt-laden air hits the rollers from multiple directions all year. Fort Lauderdale gets salt air from one side and has more inland buffer. That constant two-sided exposure corrodes factory rollers in half the time, which is why we use marine-grade aftermarket rollers on most Sea Ranch Lakes replacements. Call (754) 238-2201 for an exact quote, and we’ll check your rollers while we’re there.
Service Areas Near Sea Ranch Lakes
TruePane serves Sea Ranch Lakes and the surrounding Broward and Palm Beach communities. If you’re in Seminole, we provide CGI service in Seminole with the same local permit knowledge and salt-air expertise. Farther south, CGI service in Sewall’s Point covers Martin County’s coastal corridor. And for a full look at where we work, see our Sea Ranch Lakes service area page.
Book Your CGI Service in Sea Ranch Lakes Today
If your CGI windows or Sea Ranch Lakes Door Installation is showing salt damage, a stuck roller, or a seal that’s starting to fog, call (754) 238-2201 for a free estimate. We’ll measure every opening twice, pull the village permit the same day, and register both warranty layers in writing before we leave the driveway. The pane will be true, or the job isn’t done.
Written by Dale Kessler, Owner at TruePane Windows & Doors, serving Sea Ranch Lakes since 2008.
Six Reasons Homeowners Choose TruePane Windows & Doors
Impact systems engineered to design pressures up to +/-100, matched to your wind zone - your openings hold when the storm arrives.
Low-E insulated impact glass from our manufacturer lines commonly cuts monthly cooling bills 20-30%.
Laminated impact glass shuts out up to 40% of outside noise - traffic, neighbors, weather.
Monitoring services run $30-90 a month. Laminated impact glass resists forced entry around the clock, with no subscription.
Florida homeowners average around 25% savings on the windstorm portion of their policy after protecting every opening - some homes qualify for more.
A full impact package upgrades curb appeal, buyer confidence and appraised value in one project.